?AUTOPHIX BAS10012V 24V Auto Car Battery Tester Load Charging Cranking System Test 100-2000CCAAdopting the advanced conductance testing technology, is to help mechanics find the problem easily, quickly and accurately; testing cranking, charging, and common fault for all automotive cranking lead acid battery including ordinary lead acid battery, gel battery, AGM flat plate and spiral battery.
?Autophix BAS100 12V-24V Battery Tester Functions?
??1.Identify battery status Good or Replace ??2.Check Battery Capacity - Cold Cranking Amps (CCA), DIN, EN and IEC information relative to battery rating. ??3.Check Internal resistance value (Ohm) ??4.Display battery life in percentage (%) ??5.Battery Cranking Test, load test ??6.Battery Charging Test, Ripple Test ??7.Support battery ripple test and review test data
?Autophix BAS100 12/24V Battery Tester Features
??1.Battery Test displays
Battery Test displays SOH (State of Health), SOC (State of Charge), Voltage, Current, Rating, and the readable analysis results on readable LCD screen for your reference;
??2. Different Battery Test Result Displayed:
??1) Good Battery: The battery is in good condition, and you can rest assured of using it;??2) Good, Recharge: It?s a good battery with low current, and please recharge it before next using;??3) Replace: The battery is almost or already broken, and you should replace the battery, or there will be a bigger danger;??4) Bad Cell, Replace: The battery is broken or interiorly damaged or has short circuit, and it?s time to replace the battery;??5) Charge-Retest: Unstable battery shall be recharged and retested to avoid error. If the same test result appears again, the battery is regarded as damaged, replace the battery.
??3. Cranking Test to know the whole state of the starting system according to the data:
??1). Entering cranking test and starting the engine as prompted, tester will automatically complete the test;??2). The tester will display the result including actual cranking voltage and actual cranking time;??3). If cranking voltage value is lower than 9.6V, the cranking system is regarded as abnormal;??4). If cranking voltage value is higher than 9.6V, the cranking system is OK.
??4. Reliable data of Charging Test for your reference:
??1). Charging Volt: Normal ? the generator output is normal, no problem detected;??2). Charging Volt: Low ? check the drive belt of the generator and the connection between generator and battery, or follow the manufacturer?s suggestion to eliminate generator fault;??3). Charging Volt: High ? replace the generator assembly or a regulator to avoid battery damages;??4). No Volt Output ? check the generator connection cable and the belt;??5). Diode Test ? there is at least one diode is damaged if ripple volt is too high
?Cranking Test
Test different parts of charging system,including alternator, starter,generator,rectifier diode and so on
?Charging Test
In the ignition state,test whether the generstor module works normally through Ripple Test,Loaded test,Unload test
?Autophix BAS100 Car Motorcycle Battery Tester Application
Use to test a wide range of 12/24V batteries (Starting [SLI], Deep Cycled and Marine) of Wet (Flooded), VRLA or Maintenance Free (MF), Sealed Maintenance Free (SMF), Absorption Glass Mat (AGM) and GEL cell. The major battery standards JIS, SAE, EN, DIN and IEC are supported.
?Perfect Compatible with all 100-2000CCA
?High Accuracy and Fast Testing
Top-level APM32 chip,Quickly analyze the data and show the test results in 3 seconds. Accuracy>99.5%
?Keep Operation Safe For Every Users
Against Reverse-PolaritiesAgainst OverheatingAgainst Sparks
?12V 24V Car,Boat,Motorcycle Turck,VAT, Boat, Suv ,More... Batterise.
?Advantages of this method:
(1) It can be used for checking almost all the batteries including low capacity battery and internal resistance of the notebook battery exclusively.(2) It will not harm the battery by using this method.
