Malaysia Leading Online Shopping Marketplace

  • Jual Dengan Kami
  • Ikut Kami Di
  • Notifikasi
    Notifikasi Baharu
  • Help
  • Daftar
  • Log Masuk

Sila Log Masuk untuk melihat produk.

This seller is currently on vacation.
PL2303HX USB Transfer to TTL RS232 Serial Port Adapter Cable Module PL2303 Console Recovery Upgrade
No Rating Yet
0 Dijual
/ Per Produk

Penghantaran

Penghantaran Dari
Pulau Pinang
Anggaran Penghantaran
Apr 17, 2024 - Apr 24, 2024

Warna

Sila pilih variasi produk terlebih dahulu

Kuantiti

86 Unit lagi
Jumlah
RM 4.3
Gambaran Kedai
Trand88 Marketing and Distributors
On Vacation
Produk 365
Pengikut 8
Penilaian 5
Sertai 2 Years Ago
Kadar Pembatalan 0%
Spesifikasi Produk
Category
: Electronics Accessories  >  Network Components  >  Adapters & Converters
Brand
: Not Specified
Model
: Not Specified
SKU
: T8800044
Dimension (Length x Width x Height)
: 13.00 x 4.00 x 2.00
Weight(kg)
: 0.03
Manufacturing Country
: Not Specified
Warranty Type
: No Warranty
Warranty Value
: -
Warranty Description
: -
Hantar Dari
: Pulau Pinang
Deskripsi Produk
Note:

Setting 3.3V and 5.0V output (this is the power to the microcontroller, the need to upgrade the machine) Please pull out the small plate from the computer, set the jumper to take, do not charge it to avoid damage to the device.

Pin connection and description:

Connector pin assignments before you must find, especially GND must not be connected to the voltage pin, and RX and TX side do not connected to the VCC pin, the (actual measurement had some VCC pin voltage up to 14V.) Wrong shall be burnt chip adapter cable, be sure to note, do not take their own small board to do the experiment, otherwise we are not responsible for any burn. We must find a good pin definitions in the access. Connection method: Again Brush only need three lines, generally used only RX TX GND three signal lines, VCC no connection. The above is 4,5 needles friends, not to VCC and BT needle. Please use the RXD and target board TX phase, TXD and target board RX phase, GND connection GND, if not, were reversed RX and TX.

Connection:

RX for TX;

TX to RX;

Ground-ground (GND to GND)

USB to serial platelet function:

1 simple serial communication.

2 or ADSL router firmware upgrade.

3 GPS serial communication.

4 hard drive firmware upgrade.

5 easy to use, RX received the MCU TX; TX RX received at the MCU connected to ground. Without the need for conversion MAX232.

6 Super Terminal in use; common serial debugging tools.

7 upgrade with a variety of satellite machine.

Package included : 1 unit of a cable adapter module

#PL2303HX #TTL #RS232 #PL2303 #raspberrypi #arduino #microbit
Penilaian produk
- / 5.0
Copy Link
Copy Link
Copy
Copied to Clipboard!
  • 0 Troli Membeli-belah
  • Wishlist
  • Pusat Kupon
  • Informasi
  • Chat
  • Log Masuk / Daftar
  • What's In The Box
  • Kongsi
  • Kembali
  • Kembali Ke Atas
    • ©2024 PG Mall Sdn. Bhd. 200801035285 (836625-K). All Rights Reserved.